Bathtub Replacement How to Remodel a Bathtub
Bathtub Replacement How to Remodel a Bathtub? Is it becoming more difficult for you to clean your old bathtub as well as bathtub replacement? Are there ugly cracks and chips that seem to be getting worse with each passing day? A new bathtub need not be a difficult and time-consuming renovation project.
Before removing a bathtub, there are a lot of different factors to think about. In order to get the existing tub out of the way, you’re going to need to dismantle the three walls that surround it. If the space is limited, it is possible that the cupboard, sink, and toilet will need to be removed as well.
It is important to keep in mind that new bathtubs are wider than older bathtubs. Because of this, in order to install a new bathtub, you will first need to remove the base moulding, the floor covering, and the underlayment.
Putting in a brand new bathtub in place of an old one is a really challenging undertaking to do. During the process of removing them, a significant number of the tiles that are on the walls may damage. The renovation may go more rapidly if the outdated tub can be reached without much effort. It is a lot more difficult process to do if the old tub must be removed by opening a wall in order to make room for the new tub.
Before You Get Started Bathtub Replacement
When looking for a new bathtub, you should be aware that certain tubs are labelled as either left-side or right-side tubs. This indicates that the location of the drain hole varies depending on whether the tub is seen from the left or the right.
Because alcove bathtubs cannot be swapped out for one another, it is essential to make sure you choose the right one. What first looks to be a box with four sides is, in reality, merely a single side called the front apron.
Keeping the plumbing for the bathtub in its original location results in far less mess, labour, and expense. The price of the project will need to be increased significantly if the water supply and drainage are moved from one side to the other. If you have any doubts about your capacity to finish this pretty complicated process, you should consider having a trained expert do it for you so that you can be certain that it will be done correctly.
When Should a Bathtub Be Replaced?
The bathtub should be replaced first in a complete bathroom redesign, followed by the installation of the bathroom vanity and the toilet. This makes it possible to remove the old bathtub more easily and provides assistance while situating the new bathtub.
Concerns Relating to Safety
Before you begin, make sure that the water supply and any electrical circuits around the bathtub border are turned off. When removing the old bathtub, use extreme caution: Tubs made of cast iron and steel are both heavy. When removing cast-iron bathtubs, it is normal practise to first use a sledgehammer to break the tubs apart, and then to remove the individual parts of the tub.
What You Will Require
- Equipment / Tools
- Wrench for drains
- Pliers
- Screwdriver
- Hammer
- Cordless drill
- Prybar
- Caulk removal tool
- Allen wrench set
- Wrench with a channel-lock head
- Multi-tool with an oscillating blade
- Tape measure
- Pencil
- Chalk snap line
- Shop vacuum
- Miter saw or circular saw with an electric motor
- Caulking gun
New Bathtub Replacement
The process of putting in a new bathtub is quite similar to the one that was used to remove the old one. We are going to make the assumption that the new tub is about the same size as the previous one. If this is the case, then the piping and the fixture will line up correctly. In such case, the piping will need to be altered in order for it to be compatible with the new tub before it can be brought in. Also inspect the surfaces of the walls.
Once the bathtub is in its permanent location, you will need to either repair the existing wall surface or build a new wall surface so that the old wall can rest on the flange of the new tub. Under the tile in the tub area you should install cement backerboard. Normal drywall is not capable of withstanding the high levels of moisture that are present in these areas. Cement backerboard should not be painted.
1. Place the skids under the new tub, and have someone assist you in moving it into the area occupied by the old tub. Adjust the water supply and drain pipes so that they are aligned correctly.
When it is in its permanent location, the tub should be levelled. To level the tub, first place the level along the rim of the tub, and then place the shingle shims along the bottom of the tub. Use the appropriate number of shims to eliminate any rocking or instability. After that, attach the tub to the hangers, and if more support is required, add more hangers.
2. Join the pipes that go to the drain and the supply of water. The slip connection on the drain pipe is adjusted by simply pulling it down (or up), and then the slip nuts are tightened.
3. Plumber’s putty is used to seal the drain in the bathtub before it is pushed into place and the strainer cap is fastened .
It’s possible that the lift rod for the drain stopper has a configuration similar to a turnbuckle. You will need to rotate the turnbuckle in order to adjust the linkage and ensure that the drain stopper fits snugly into the aperture at the base of the bathtub.
4. The hot and cold water faucets are screwed into the fittings on the supply pipes. When tightening the fixtures, joint compound should only be applied to the male threads in order to seal the threads. Escutcheons are typically secured in place with a set screw and are designed to fit over the apertures of faucets. To conclude the job, attach the handles for the hot and cold water faucets .
5. Take a measurement for the tub spout by starting at the face of the drain nipple in the wall and going all the way to the other face of the wall. The next step is to take a measurement that includes an additional half an inch to an inch and a half of an inch from the threaded connection that is located within the spout. You will need to lengthen the nipple in order to accommodate the threads if the spout is either too long or too deep to accommodate them.
6. If you have to cut any of the lines in order to remove the tub, you will need to repair those pipes. Start at the earliest connection you can locate and work your way toward the tub from there. Put back in place any additional fittings or fixtures that you may have had to remove. Check for leaks in the lines once the water supply has been turned on. Make modifications as required.
7. Complete the wall that surrounds the bathtub. In the event that you need to rebuild the wall that is located around the tub, we suggest that you utilise cement backerboard. On the other side of the frame, regular drywall might be used instead. Replace the old framework that was taken out to create way for the removal of the tub with new framing. After the drywall has been applied, the wall must next be taped, sanded, and finished.
In the event that you need to remove the panel once again for repairs, you may wish to make a notation on it and place it next to the baseboard.
Advice for Bathtub Replacement How to Remodel a Bathtub
For easy installation, search for matching bathtubs and wall surrounds. Because of the tendency for them to be brand- and model-specific, you won’t be able to match the wall surround of one manufacturer with the tub of another company.
If the bathtub cannot be reached easily from a floor below, you should install a permanent access panel in the room that is next to the bathtub. This is helpful in the event that you ever need to inspect or repair the plumbing in the bathtub in the future.
It is not required that the waste and overflow drain assembly measuring 1-1/2 inches be constructed from scratch using individual parts. Always keep the above things in your mind when Bathtub Replacement How to Remodel a Bathtub. Share your thoughts in our comments section.
No Comments
Leave Comment